The purpose of this experiment was to learn about metal hydride reduction reactions. Therefore, the sodium borohydride reduction of the ketone, 9-fluorenone was performed to yield the secondary alcohol, 9-fluorenol. Reduction of an organic molecule usually corresponds to decreasing its oxygen content or increasing its hydrogen content. In order to achieve such a chemical change, sodium borohydride (NaBH4) is used as a reducing agent. There are other metal hydrides used in the reduction of carbonyl groups such as lithium aluminum hydride (LiAlH4). Nevertheless, the latter is not used in this experiment since it is very reactive and extremely flammable. On the contrary, NaBH4 is relatively mild and it can be used with protic solvents. In this manner, 1.507 grs of the ketone 9-fluorenone were mixed with 30.0 ml of 95% ethanol in a 125 ml Erlenmeyer flask. The bright yellow mixture was stirred during 7 minutes until all the components were dissolved. It is important to allow the ketone to dissolve completely in the solvent in …show more content…
The yellow solution containing the reactants was slowly poured into the beaker containing the cold water and the acid in order to cause the precipitation of the alcohol, 9-fluorenol and to destroy (hydrolyzed) the unreacted excess sodium borohydride. Subsequently, the white precipitate was vacuum filtered and washed twice with 20.0 ml portions of distilled cold water by pouring the liquid into the Buchner Funnel during filtration. It was necessary to wash the alcohol prior to recrystallization considering that the C-OH bond is easily broken by the formation of a stable and benzylic carbocation that favors the synthesis of difluorenyl ether. Finally, before the purification by recrystallization of the obtained product, the white solid alcohol was allowed to dry over a period of a
Discussion 1. Zn0 (s)+ Cu2+S6+O42-(aq) →Cu0(s) + Zn2+S6+O42-(aq) Zn0(s) → Zn2+(aq) + 2e- Cu2+(aq) + 2e- → Cu0(s) Zn0(s) + Cu2+(aq) → Zn2+(aq) + Cu0(s) Oxidant (oxidizing agent) is the element which reduces in experiment.
In this lab, the oxidation of a secondary alcohol was performed and analyzed. An environmentally friendly reagent, sodium hypochlorite, was used to oxidize the alcohol, and an IR spectrum was obtained in order to identify the starting compound and final product. The starting compound could have been one of four alcohols, cyclopentanol, cyclohexanol, 3-heptanol, or 2-heptanol. Since these were the only four initial compounds, the ketone obtained at the end of the experiment could only be one of four products, cyclopentanone, cyclohexanone, 3-heptanone, or 2-heptanone. In order to retrieve one of these ketones, first 1.75g of unknown D was obtained.
Nucleophilic Substitution: Preparation of 1-Bromobutane and Alkyl Halide Classification Tests Introduction This procedure was undertaken in order to convert a primary alcohol, 1-butanol, into a primary alkyl halide, 1-bromobutane. This was done using hydrobromic acid. Additionally, tests were performed to assess the degree of the alkyl halide: primary, secondary or tertiary.
1. Identify the range of senses involved in communication • Sight (visual communication), Touch (tactile communication), Taste, Hearing (auditory communication), Smell (olfactory communication) 2. Identify the limited range of wavelengths and named parts of the electromagnetic spectrum detected by humans and compare this range with those of THREE other named vertebrates and TWO named invertebrates. Figure 1: the electromagnetic spectrum source: www.ces.fau.edu Vertebrates Human Japanese Dace Fish Rattlesnake Zebra Finch Part of electromagnetic spectrum detected ROYGBV (visible light) detected by light sensitive cells in the eye called rods and cones.
Tyler White CHEM151LL 32658 04/01/2018 Different Types Chemical Reaction Types and Equations Purpose: The purpose of this lab experiment is to examine different types of chemical reactions such as Decomposition reaction, Synthesis reactions, Combustion reactions, and different Chemical equations. The experiments were conducted online using Late Nite Labs. Materials: Because the experiments were conducted online there wasn’t any physical use of materials, only digital ones, for these labs to be performed. Only the registration for the website was needed to perform these online labs, as well as a desktop computer.
1. Introduction The objective of the experiments was to determine the identity of an unknown compound in order to properly dispose it. The process of disposal is very important when dealing with chemicals. Some chemicals are very
The goal of the experiment is to synthesize a bromohexane compound from 1-hexene and HBr(aq) under reflux conditions and use the silver nitrate and sodium iodide tests to determine if the product is a primary or secondary hydrocarbon. The heterogeneous reaction mixture contains 1-hexene, 48% HBr(aq), and tetrabutylammonium bromide and was heated to under reflux conditions. Heating under reflux means that the reaction mixture is heated at its boiling point so that the reaction can proceed at a faster rate. The attached reflux condenser allows volatile substances to return to the reaction flask so that no material is lost. Since alkenes are immiscible with concentrated HBr, tetrabutylammonium bromide is used as a phase-transfer catalyst.
Aims of experiment • Determine the rate constants for hydrolysis of (CH3)3CCl in solvent mixtures of different composition (50/50 V/V isopropanol/water and 40/60 V/V isopropanol/water) • Examine the effect of solvent mixture composition on the rate of hydrolysis of (CH3)3CCl Introduction With t-butyl chloride, (CH3)3CCl, being a tertiary halogenoalkane, it is predicted that (CH3)3CCl reacts with water in a nucleophilic substitution reaction (SN1 mechanism), where Step 1 is the rate-determining step. The reaction proceeds in a manner as shown
Chem 51LB Report Ngoc Tran - Student ID # 72048507 The purpose of this lab is to examine the composition of three components of gas products of elimination reaction under acidic condition by conducting the dehydration of primary and secondary alcohol, and under basic condition by conducting the base-induced dehydrobromination of 1-bromobutane and 2-bromobutane. Then gas chromatography is used to analyze the composition of the product mixtures. Gas chromatography (mobile phase) is used to analyze the composition of three components of the gas products. A syringe needle with gas product is injected into the machine, and the component is eluted and the composition is related to the column or the peaks.
Benzyne Formation and the Diels-Alder Reaction Preparation of 1,2,3,4 Tetraphenylnaphthalene Aubree Edwards Purpose: 1,2,3,4-tetraphenylnaphthalene is prepared by first producing benzyne via the unstable diazonium salt. Then tetraphenylcyclopentadienone and benzyne undergo a diels-alder reaction to create 1,2,3,4-tetraphenylnaphthalene. Reactions: Procedure: The reaction mixture was created. Tetraphenylcyclopentadienone (0.1197g, 0.3113 mmol) a black solid powder, anthranilic acid ( 0.0482g, 0.3516 mmol) a yellowish sand, and 1,2-dimethoxyethane (1.2 ml) was added to a 5-ml conical vial.
Vacuum filtration was performed on the crude product, then it was recrystallized for purification. Melting point analysis was conducted on the recrystallized product to determine its identity. 3. The three possible mechanisms in this experiment were syn-addition
However, after refluxing for a while, yellow precipitates begin to form near the top of the flask. It was assumed that the remaining starting material was concentrated from a decrease volume to reappeared in solution. Nevertheless, this may have been a sign of contamination that will negatively affect the entire reaction. This observation later resulted in a yellowish
Abstract: The purpose of this experiment was to identify given Unknown White Compound by conducting various test and learning how to use lab techniques. Tests that are used during this experiment were a flame test, ion test, pH test, and conductivity test. The results drawn from these tests confirmed the identity of the Unknown White Compound to be sodium acetate (NaC2H3O2) because there were no presence of ions and sodium has a strong persistent orange color. The compound then will be synthesized with the compounds Na2CO3 and HC2H3O2 to find percent yield.
Experiment 2 Report Scaffold (Substitution Reactions, Purification, and Identification) Purpose/Introduction 1. A Sn2 reaction was conducted; this involved benzyl bromide, sodium hydroxide, an unknown compound and ethanol through reflux technique, mel-temp recordings, recrystallization, and analysis of TLC plates. 2. There was one unknown compound in the reaction that was later discovered after a series of techniques described above.
Purpose/Introduction The process of recrystallization is an important method of purifying a solid organic substance using a hot solution as a solvent. This method will allow the separation of impurities. We will analyze Benzoic Acid as it is dissolved and recrystallized in water and in a solvent of Methanol and water. Reaction/Summary