Summary Of The Lab Mixed Substances

Introduction The purpose of this Lab was to identify the density of the unidentified object and determine what substance the unidentified object given by the teacher was. The density calculated in the experiment will stay the same because the density of the unidentified object will stay constant. The Independent Variable of this experiment was the calculated density and the unidentified object given. The Dependant Variable for this experiment was the density.

Fiona Young Ha Hoang and Joey Lu 12/11/15 Malik AP Chem 4th Prepare to Dye Introduction Chromatography is the separation of a mixture or substance by putting it in a solute with chromatography paper. Following with this lab, we take 3 colors of food dye (red, yellow, and blue) and test which solvent out of distilled water, acetone, ethanol, and 2-propanal would separate the molecules in the dyes the best.

The lab started off by measuring critical materials for the lab: the mass of an an empty 100 mL beaker, mass of beaker and copper chloride together(52.30 g), and the mass of three iron nails(2.73 g). The goal of this experiment is to determine the number of moles of copper and iron that would be produced in the reaction of iron and copper(II) chloride, the ratio of moles of iron to moles of copper, and the percent yield of copper produced. 2.00 grams of copper(II) chloride was added in the beaker to mix with 15 mL of distilled water. Then, three dry nails are placed in the copper(II) chloride solution for approximately 25 minutes. The three nails have to be scraped clean by sandpaper to make the surface of the nail shiny; if the nails are not clean, then some unknown substances might accidentally mix into the reaction and cause variations of the result.

I think that these properties were not tested because it would have taken much longer to check the mass, and boiling point. Testing for the scent of each of the powders may haven’t been much of a help as they probably all smell very similar. Also, we don’t have a stove top in the science classroom so checking the boiling point would be difficult. Another reason as to why that we didn’t check mass is because it would have been difficult to get the exact same amount of each substance for the measurements would be accurate. Finally, all those physical properties would result in quantitative measurements and we didn’t include any other quantitative measurements in this

I. Purpose: To experimentally determine the mass and the mole content of a measured sample. II. Materials: The materials used in this experiment a 50-mL beaker, 12 samples, a balance and paper towels. III.

3. Upon adding 20 drops of NaOH, a white precipitate was formed signifying acidic impurity. In the second NaOH mixture, about 20 drops were administered and no precipitate formed indicating that the ample is more pure than before. Data: Weight of flask = 75.10 grams Weight of the flask with solids =

Abstract: The purpose of this experiment was to identify given Unknown White Compound by conducting various test and learning how to use lab techniques. Tests that are used during this experiment were a flame test, ion test, pH test, and conductivity test. The results drawn from these tests confirmed the identity of the Unknown White Compound to be sodium acetate (NaC2H3O2) because there were no presence of ions and sodium has a strong persistent orange color. The compound then will be synthesized with the compounds Na2CO3 and HC2H3O2 to find percent yield.

During the Mixed Substances lab the objective was to see how many properties of individual substances compare with properties of mixed substances. From here on the words that would help you along the way of the lab for your research is mixture, homogeneous mixture, and last but least heterogeneous mixture. The hypothesis or guess on what would happen when the water is mixed with the cornstarch, is the cornstarch and water will mix and form a new liquid/solid. However, the Investigating Mixtures lab objective was to observe that not all liquids behave the same way when mixed with other liquids. Moreover the hypothesis of this experiment was that the vegetable oil and colored will separate because the vegetable oil will go to the top and the

The objective of the sludge lab was to determine how many different pure substances were in the sludge by using the methods and techniques we have learned throughout the year. We had to pick separation methods so we could separate our sludge and then test characteristic properties on our separated liquids and solids. This experiment made us use our knowledge on characteristic properties to pick the ones we should test to help us identify our pure substances. Characteristic properties are properties that help identify a solid or liquid. Each solid or liquid has a certain density, boiling point, solubility, flammability, so if you know what each one is then you can use that information to help you identify your solid or liquid.

CLAIRE MUNTING 29/01/2018 Criterion C EFFECTS OF SURFACE AREA OF CALCIUM CARBONATE UPON RATE OF REACTION Calcium Carbonate Chips 1 Introduction: Within the current investigation, the effects of the surface area of Calcium Carbonate (CaCO3) in combination with Hydrochloric acid (HCl) upon its rate of reaction. CaCO3, commonly referred to as limestone, is an organic substance and is, in a sense, the crystallised “carbonic salt” of the element, calcium2. In addition to being a salt, the pH level of Calcium Carbonate is 9.91, and it is therefore, a basic substance, due to the fact that it is comprised of a pH level higher than 7, which is neutral3. HCl, however, is the bodily acid found in the stomach of human beings.

Experiment 2: Distillation and Purification of Liquids Angela Kaiser 100125701 ELL 308 September 19th, 2015 Introduction and Experimental: The purpose of this experiment was to determine the ratio of dichloromethane (DCM) to cyclohexane in a DCM/cyclohexane solution by carrying out a fractional distillation. The temperature and volume of distillate were measured periodically to determine the volume both components in the solution. The experiment was performed as written in “Experiment 2: Distillation and Purification of Liquids” from the Chemistry 2050 Lab Manual for Organic Chemistry Part 1, Fall 2015. Results and Observations:

Properties of Substances Express Lab 1)The purpose of this lab was to compare the physical properties of different types of solids and how the properties of solids are determined by their intermolecular forces and their intramolecular bonds. Then we were to classify each type of solid as either ionic, metallic, non-polar molecular, polar molecular, or network. Paraffin wax classified as a non-polar molecular, Silicon dioxide was classifies as a network, Sodium chloride was classified as ionic, Sucrose was classified as polar molecular and Tin was classified as metallic. (2)The intermolecular forces that are present in Paraffin wax are dispersion forces, because it is non-polar and carries a negative charge. Followed by Sucrose that has

Also, although this likely served no contribution in disheveling the results, using a stirrer of the same material to ensure the separate testing of each substance will be as uniform as

Then we put the same measurement of cornstarch in the beakers and stirred with a spoon.

Introduction The goal of the experiment is to examine how the rate of reaction between Hydrochloric acid and Sodium thiosulphate is affected by altering the concentrations. The concentration of Sodium thiosulfate will be altered by adding deionised water and decreasing the amount of Sodium thiosulphate. Once the Sodium thiosulphate has been tested several times. The effect of concentration on the rate of reaction can be examined in this experiment.